Introducing
DabTabs GOTM
ilo’s DabTabs™ Go All-In-One is the first and only ultra-portable vaporizer designed exclusively for DabTabs™ dablets.
A safer way to consume concentrates, extracts and CBD.
Learn more about engineering behind the DabTabs™ brand below.
vaping reinvented.
The DabTabsTM brand was founded by ilo VaporTM with a focus on bringing a convenient and accurate vaporization experience to their customers.
DabTabsʼ first product to be released were DabTabsTM dablets – a brand new way to consume concentrates, extracts or CBD. DabTabs dablets offer a clean, easy, convenient way to vaporize concentrates/extracts/CBD while retaining the full-flavor, full spectrum without combustion.
Best of all, there’s virtually zero cleanup – no burned wax to scrape off and no excess oil to reclaim.
– Andrew Tarantola, Engadget
OUR TOP 6 RECOMMENDED DEVICES
1.
Puffco Peak
Step 1.
Choose your heat setting: green for flavor, red for clouds. Double-tap to begin 20 sec. heat cycle
Step 2.
Wait between 10-15 seconds to drop in dablet
Step 3.
After device vibrates, double-tap to start another heat cycle
Step 4.
Drop in dablet so it lays flat and carb cap immediately
Step 5.
Wait a few seconds for first inhale
Step 6.
Continue to double-tap as needed to produce more vapor
Enjoy!
This device is an Indirect Ceramic – a device where the vaporizable product is heated in a way where it is never exposed to the direct heat source.

2.
KandyPens Crystal
Step 1.
Place the dablet flat on theheating element
Step 2.
Press fire/heat button for approximately 10-30 seconds until vapor begins collecting
Step 3.
While still pressing the fire/heat button, begin drawing slowly as to not cool the chamber
Pulsing heat on and off at this point prevents excessive heating of the dablet and produces a more pleasant vapor
Step 4.
Release fire/heat button when done inhaling
Enjoy!
These vaporizing products are heated using resistive wires wrapped around a quartz rod, usually directly touching the vaporizable product. Quartz has less heat retention than the ceramic, so continual heating is usually required.

3.
Dr. Dabber Aurora
Step 1.
Place the dablet flat on theheating element
Step 2.
Press fire/heat button for approximately 10-30 seconds until vapor begins collecting
Step 3.
While still pressing the fire/heat button, begin drawing slowly as to not cool the chamber
Pulsing heat on and off at this point prevents excessive heating of the dablet and produces a more pleasant vapor
Step 4.
Release fire/heat button when done inhaling
Enjoy!
These vaporizing products are heated using resistive wires wrapped around a quartz rod, usually directly touching the vaporizable product. Quartz has less heat retention than the ceramic, so continual heating is usually required.

4.
Yocan Evolve
Step 1.
Place the dablet flat on theheating element
Step 2.
Press fire/heat button for approximately 10-30 seconds until vapor begins collecting
Step 3.
While still pressing the fire/heat button, begin drawing slowly as to not cool the chamber
Pulsing heat on and off at this point prevents excessive heating of the dablet and produces a more pleasant vapor
Step 4.
Release fire/heat button when done inhaling
Enjoy!
These vaporizing products are heated using resistive wires wrapped around a quartz rod, usually directly touching the vaporizable product. Quartz has less heat retention than the ceramic, so continual heating is usually required.

5.
Shatterizer
DabTabsTM Edition
Step 1.
Place the dablet flat on theheating element
Step 2.
Press fire/heat button for approximately 10-30 seconds until vapor begins collecting
Step 3.
While still pressing the fire/heat button, begin drawing slowly as to not cool the chamber
Pulsing heat on and off at this point prevents excessive heating of the dablet and produces a more pleasant vapor
Step 4.
Release fire/heat button when done inhaling
Enjoy!
These vaporizing products are heated using resistive wires wrapped around a quartz rod, usually directly touching the vaporizable product. Quartz has less heat retention than the ceramic, so continual heating is usually required.

6.
DabTabsTM Go
on the Väri Battery
Step 1.
Unscrew the mouthpiece from the DabTabsTM Go and place the dablet flat in the chamber, re-screw the mouthpiece back onto the Go
Step 2.
Screw on the DabTabsTM Go to the Väri Battery
Step 3.
Keeping the battery upright, gently tap the heat setting panel 5 times to turn the battery on
Step 4.
Tap 3 more times to cycle through the settings, we recommend red for optimal vaporization
Step 5.
Begin inhaling slowly to heat up the chamber and release
Step 6.
Draw for 5-7 seconds and enjoy! Continue to inhale as much as needed to produce more vapor.
Enjoy!
These vaporizing products are heated using resistive wires wrapped around a quartz rod, usually directly touching the vaporizable product. Quartz has less heat retention than the ceramic, so continual heating is usually required.
